Slide is a Procut, cerakoted grey to match the grip, Wilson/Vickers FO front and Tritium U notch rear, complete slide internals, used, unknown rd count, two tiny dings in the cerakote by the front sight dovetail. $320 shipped *sold* these are not suppressor height sights.
TXG grip, medium...
SOLD. Govt frame is carbon steel, it does need decking, and the barrel seat cut, besides the usual hammer/sear pin holes. Previous owner cold blued it. Ejector pin hole on right side is under sized, will need to be opened up. Bit of an undercut trigger guard, checkered front strap, .25 grip...
Used is fine, but priced accordingly if anything needs to be replaced prior to use. I don’t mind paying shipping if you’re not in New Orleans. Would prefer to pay with PP, as that’s where my fun money is at the moment.
WTS/T 1903A4 project
Part out break down:
SPF Barreled action with buggered up base and screws, plus the NOS bolt parts $1200 plus shipping SPF
With NOS barrel $1350 plus shipping
With barrel and stock/stock hardware $1500 plus shipping
SOLD Original Redfield base with windage...
WTT 6 digit SA Garand barreled receiver and complete stock, re parked and has lead-dipped heal. Has all receiver parts but the bolt. No op rod, gas cylinder or plug, or trigger group. SA 7-46 barrel, likely post war rebuild. Stock and handguards have matching grain, believe to be walnut, P...
TRADE PENDING
Want to trade, and trade only, for a SG Garand in .30-06 plus cash. Manufacturer makes no difference, would prefer a WW2 receiver though. Low ME/TE, nice wood (no cracks/major dents). Would also trade plus cash for a barreled Garand action with a low me/te barrel, but more...
WTS S&W 6" model 617 no dash, with or without grips. Target hammer, target trigger has been thinned and grooves smoothed out. One scratch on either side of the barrel that should clean up fine with a scotch brite pad, and another scratch on the side plate that should also come out fine. No...
Looking for a Remington M1903A3 receiver, with or w/o bolt, drilled and tapped preferably, complete sporters considered. Not interested in former drill rifles. Please pm or email pics. Prefer FTF New Orleans area/West Bank.
Gen 4 Glock 26 for sale only. $500 firm. Location West Bank/New Orleans area ONLY, for personal reasons I cannot travel very much (meet in Algiers, Gretna, Harvey).
Recently purchased from another member here, very few rds fired, was missing two of the four backstraps, pinky extension...
Gen 4 Glock 26 for trade only. Location West Bank/New Orleans area ONLY, for personal reasons I cannot travel very much (meet in Algiers, Gretna, Harvey).
Recently purchased from another member here, very few rds fired, was missing two of the four backstraps, pinky extension baseplates on...
Want to Trade, and trade only: 4" Smith and Wesson CS-1, with box, docs, and original serial number windowed grips. Located New Orleans/West Bank. This is the Customs Service revolver, not made in great quantity, many of which were destroyed by the Clinton admin after Customs switched over to...
The 4 CMI M14 mags are new, still in the blue plastic, $100 shipped, as they would be from 44Mag, $90 FTF in the New Orleans/West Bank area. Would also trade 1for1 for used/great cond. Glock 19 15rd mags, or all four for 3 new G19 mags.
AMMO is SOLD, AK mags are SOLD.
WTB Officers/compact 1911 frame, complete or stripped. Single stack, non-ramped barrel preferably. Located around New Orleans, but would pay to have it shipped if it's a good deal. Used is fine, new is better. Note: I am well aware one can be ordered from Fusion or Caspian, trying locally...
I know I'll regret selling, but with a baby on the way, need to re-home this outstanding rifle. I've put about 150 rounds through it, not a single malfunction. It's more accurate than I am. LC 7.62 NATO is all I've run through it. Specs:
All USGI parts except for:
Sadlak NM spring guide...
As title states, please let me know if you have a set of the pins and spring, or trunnion, latch bits, etc. I'm not against making the pins from drill bits, but would prefer the real parts. For the booster, prefer Manticores extended krink, but CNCs world be fine, too. 24mm threads. Can do PP...
http://www.vortexoptics.com/product/vortex-viper-pst-2-5-10x32-ffp-riflescope-with-ebr-1-mrad-reticle/reticle
It's used, but only one trip to the range to sight it in. Ring marks possible, as the ARMS rings are still on the scope.
For sale only now, $650 without rings, $700 with...
Like the title says, located in New Orleans, but willing to drive about an hour or so away. Prefer a new Nodak or at least one that's dimensionally correct and ready to go (rails in, center support, etc.). Not set on caliber. Also looking for parts for the build, AK102 type build, similar to...